Connection Types Wiki · Pipe threads

Male NPSM Washer-Sealed Faucet Shank

A straight parallel external pipe thread (typically 1/2-14 NPSM) on the mounting and water inlet shank of North American plumbing faucets. It serves both to secure the faucet to the deck or basin via a mounting locknut and to mate with a swivel supply connector.

Illustration of a Male NPSM Washer-Sealed Faucet Shank
Stands for
NPSM = National Pipe Straight Mechanical (or American National Standard Straight Pipe Thread for Free-Fitting Mechanical Joints)
Gender
male
Connects by
threaded, compression, fastened
Standards
ASME B1.20.1; ASME A112.18.1 / CSA B125.1; ASME B1.20.1 (NPSM thread); ASME B1.20.1 (NPSM thread form and dimensions); ASME A112.18.6 / CSA B125.6; ASME B1.20.1 (NPSM thread; specified external class 2A)
Regions
North America, United States, Canada, worldwide

How it connects

Straight parallel threads carry a mounting locknut to clamp the fixture, while fluid sealing at the inlet is achieved mechanically when a mating female swivel nut compresses an elastomeric gasket or washer against the shank end face.

Male and female halves

Male externally threaded shank. Mates with female NPSM swivel supply nuts (fluid seal via gasket) and female threaded basin mounting locknuts (structural mounting).

Usually connects to

Common sizes

  • Common 1/2-14 NPSM male shank: about 0.825–0.840 in (20.96–21.34 mm) major diameter, 14 TPI; one specified example uses external class 2A.
  • Heavy commercial/utility versions may use 3/4-14; check the actual supply-line match.

Where it is used

Residential/commercial sink plumbingDeck-mount kitchen/lavatory and utility-sink faucetsHot/cold fixture supplies

Variations

  • 1/2-14 NPSM brass or plastic/POM shank
  • Integral cast/extruded shank or nipple extension
  • Dual-shank centerset or single-hole mounting tube
  • Different lengths/materials with matching thread and sealing face

How to recognise it

Recognised as an externally threaded tubular stud or threaded tube projecting downwards beneath a sink faucet body. The threads are cylindrical (not tapered) and run long enough to accommodate countertop thickness and a locknut.

Often confused with

Confused withHow to tell them apart
NPT pipe threadNPT threads are tapered (1:16 taper) and seal on the thread flanks with thread sealant; NPSM faucet shanks are straight parallel threads requiring a gasketed swivel nut or union. NPT has tapered threads designed to seal on the thread flank with sealant, whereas NPSM is straight/parallel and requires an elastomeric gasket/cone washer at the flat face. NPT tapers and forms a thread-based seal with suitable sealant. This inlet has parallel threads and uses the supply washer at its end; matching nominal pipe size alone is insufficient.
G 1/2 (BSPP) male thread1/2" BSPP (ISO 228) has a 55-degree thread flank angle and 14 TPI with slightly different pitch diameter (~20.95 mm OD) compared to 60-degree NPSM (OD ~21.34 mm). BSPP has a 55° Whitworth thread angle with 14 TPI and slightly different pitch diameter (~20.95 mm) compared to the 60° ANSI/ASME thread angle of 1/2"-14 NPSM. G 1/2 has a 55-degree thread angle and 14 TPI with slightly different pitch diameter (~20.95 mm) compared to North American 60-degree NPSM (~21.3 mm).

Also called

1/2" IPS Faucet ShankBasin Cock Shank Thread1/2" NPS faucet inlet shank1/2" straight pipe faucet shankfaucet mounting shank1/2-14 NPSM male faucet shank; 1/2-14 NPSM male faucet inletStraight-thread faucet supply shank

Good to know

In North American retail plumbing, 1/2" NPSM faucet shanks are frequently labeled colloquially as '1/2" IPS' or '1/2" FIP/MIP supply connection', but technically IPS refers to pipe size and the thread form used on faucet shanks is ASME B1.20.1 NPSM straight mechanical thread. Additional standard references: ISO 228-1; EN 1113.

Related connections

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro