Connection Types Wiki · Hose & tube fittings

Female SAE 45° Flare Fitting

Female 7/8-14 UNF straight internal thread of an SAE 45° flare nut for 5/8 in OD tube (SAE size -10). The nut clamps a 45° flared tube end onto a male 45° flare cone; the seal is metal-to-metal at the flare, not at the thread.

Illustration of a Female SAE 45° Flare Fitting
Stands for
SAE = Society of Automotive Engineers; UNF = Unified National Fine thread; 7/8-14 = 0.875 in major diameter, 14 threads per inch.
Gender
female
Connects by
threaded, compression, clamp
Standards
SAE J512; SAE J513 (refrigeration tube fittings; claimed interface family, not verified certification of the sample part); ASME B1.1 (UNF threads); ASME B16.26
Regions
North America, Worldwide, including HVAC/refrigeration

How it connects

Nut slides over the tube, the tube end is flared 45°, and the nut threads onto the male flare fitting, pressing the flare between the nut's internal 45° face and the fitting cone for a metal-to-metal seal. Thread only holds; no sealant.

Male and female halves

This is the female half (nut, internal 7/8-14 UNF thread, internal 45° seat). Mates with a male SAE 45° flare fitting (external thread + 45° cone).

Usually connects to

Common sizes

  • SAE 45° flare sizes run from 1/8 in tube to about 1 in; 5/8 in is -10 and 3/8 in is -6.
  • Listed tube/thread pairs: 1/8 → 5/16-24, 1/4 → 7/16-20, 5/16 → 1/2-20, 3/8 → 5/8-18, 1/2 → 3/4-16, 5/8 → 7/8-14 and 3/4 → 1-1/16-14.
  • A separate 3/8 in example lists 9/16-24 UNEF-2B (0.5625 in, 24 TPI), conflicting with the 5/8-18 pairing; confirm the specific fitting.
  • For 1/4 in (6.35 mm) tube, 7/16-20 UNF converts to 11.1125 mm major diameter and 1.27 mm pitch; these are nominal conversions.

Where it is used

HVAC/refrigeration lines and mini-splitsRefrigerant charging/manifold/service hosesNatural/LP-gas appliances and hosesFuel/oil lines, including automotiveLow-pressure hydraulics

Variations

  • Short, long/rod or forged flare nut
  • Blind flare cap
  • Forged or bar-stock brass
  • Straight or 45°/90° elbow swivel, including female-female hose ends; body angle is separate from the 45° seat
  • Female adapter/union body

How to recognise it

Hex brass nut with a straight internal 7/8-14 thread (about 22.2 mm major diameter) and a 45° conical seat inside at the back, with a bore through for the 5/8 in tube. Often a tapered/chamfered nose on the tube side.

Often confused with

Confused withHow to tell them apart
JIC 37° flareSame 7/8-14 thread on some sizes but 37° seat instead of 45°; JIC is usually steel hydraulic, SAE 45° usually brass HVAC/gas. Not interchangeable for sealing. May share 7/16-20 threads, but the seat angle is 37° instead of 45°. Thread engagement alone does not establish compatibility. JIC -6 uses 9/16-18 thread and a 37° seat; 5/8-18 with 45° seat is SAE flare 3/8. Measure seat angle.
SAE O-ring bossSame thread but seals with an O-ring on a flat face/port, with no flare cone. Uses an O-ring sealing arrangement rather than a mating 45° flare seat. The thread designation alone is insufficient.
NPT female threadNPT is tapered and seals on the thread; flare nut thread is straight.

Also called

5/8 in SAE 45° flare nut; SAE 010110 / 010166 flare nut (5/8 tube)-10 SAE flare nut; 3/8 SAE 45 flare nut; 7/8-14 flare nut1/4 inch SAE female flare swivel; 1/4 inch female flare (FFL) swivel7/16-20 female SAE 45° flare3/8 female flare swivel; 3/8" Fine Thread Flare Female; 3/8 flare female (propane/LP)FFL swivel 3/8-6 SAE 45 female swivel3/8" Tube OD 9/16-24 Flare Nut/Fitting

Good to know

Thread size alone does not define the connection: 7/8-14 UNF is shared with JIC 37° and SAE ORB -10. The 45° flare angle is what identifies SAE flare. In HVAC it is usually written as just '5/8 flare'.

Related connections

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro