How it connects
The nominal 4x4 wood post seats into the open U-channel cradle base and is fastened through pre-drilled side holes using lag screws, structural wood screws, or through-bolts.
Male and female halves
Female cradle receptacle mating with a male squared end of a nominal 4x4 wooden post.
Usually connects to
- Matching square-cut solid/engineered timber, glulam or wood column, including nominal 4 × 4 (3.5 in actual) and 6 × 6
- Round/tubular steel fence post or Schedule 40 galvanized pipe on the corresponding saddle variant
Common sizes
- Wood-post bases commonly fit nominal 4 × 4, 4 × 6, 6 × 6 and 8 × 8 lumber, with actual sizes 3.5 × 3.5, 3.5 × 5.5, 5.5 × 5.5 (139.7 mm) and 7.5 × 7.5 in.
- A 4 × 4 cradle is about 3.5–3.6 in (89–91 mm) wide with 1–6 in flanges. Larger/rough-sawn bases reach 10 × 10 or 12 × 12; descriptions include 11-1/2 in dressed and 254 mm rough-sawn widths.
- Pipe-post saddle variants list nominal 1-1/2, 2 and 2-1/2 in, with 1-7/8, 2-3/8 and 2-7/8 in ODs; these are separate profiles.
Where it is used
Deck and porch framingPergolas/gazebos/patio coversResidential/agricultural fencesStructural timber post-to-foundation jointsPorch rails
Variations
- Embedded wet-concrete or surface-bolted base
- Flush or adjustable standoff, including 1 in plate
- Two-piece adjustable base
- Concealed knife plate
- Open U-seat/two cheeks
- Enclosed four-sided bucket/collar with flanges
- Open pipe saddle/inline pipe-grip tie
How to recognise it
Recognised as an open-sided, U-shaped stamped or welded sheet metal bracket with a flat floor and two vertical side flanges containing fastener holes spaced approximately 3.5 to 3.6 inches apart.
Often confused with
| Confused with | How to tell them apart |
|---|---|
| 4x4 closed post base socket / boot | A closed post socket or sleeve encases all 4 vertical faces of the post, whereas a cradle has open U-shaped opposing sides. |
| rough-cut 4x4 post bracket | Rough-cut brackets measure a true 4.0 in x 4.0 in inside, whereas nominal brackets measure 3.5 in to 3.6 in inside. |
| Wood End | Wood End refers to the male end-grain face of the timber post itself, whereas this connection is the female metal bracket receptacle/seat that the post sits into. |
| Post cap saddle | A post cap saddle mounts at the top of a post to receive a horizontal beam or girder, whereas a post base bearing seat supports the post bottom at the foundation or deck. |
| Kee Klamp / slip-on structural pipe fitting | Kee Klamp fittings are cast iron or aluminum structural fittings locked using radial set screws rather than a bent sheet-metal clamping saddle with a transverse through-bolt. |
Also called
4x4 post base cradleU-shaped 4x4 post bracket; U-shaped post base; 4x4 post anchor bracket4x4 post saddle; post shoe socket; post saddle femalepost base bucketpost bracket seatpipe grip tie clamp; pipe tie collarpipe saddle clampmetal post to wood fence bracket clamp
Good to know
Commonly manufactured by structural connector companies such as Simpson Strong-Tie (e.g. EPB, ABU, PBS series) and various outdoor structural hardware brands.
Related connections
Design with real parts
Crafti checks which parts connect, right in your browser.


