Connection Types Wiki · Framing, rails & extrusion

Woodworking T-Track Channel

A standard woodworking extruded aluminum channel featuring a stepped or double-cut internal T-slot cavity. It is designed to capture and allow linear sliding of fastener heads, accepting 1/4" and 5/16" T-bolts as well as standard 1/4" hex head bolts.

Illustration of a Woodworking T-Track Channel
Stands for
T-track = T-slot track extrusion.
Gender
female
Connects by
insertion, fastened, clamp, friction, threaded, other
Standards
De facto North American woodworking industry standard (Rockler, POWERTEC, Kreg, Incra); De facto woodworking standard (3/4" x 3/8" miter gauge slot with T-retaining flange); De facto North American woodworking standard (3/4" x 3/8" miter slot)
Regions
North America, worldwide

How it connects

Fastener heads or sliding nuts insert from either open end (or a drop-in slot) and slide along the channel. Tightening a knob or nut draws the bolt head upward against internal retaining lips to clamp accessories in place.

Male and female halves

Female channel profile that captures male sliding fasteners (T-bolts, hex bolts, or sliding nuts).

Usually connects to

Common sizes

  • Typical track exterior: 3/4 in wide × 3/8 in deep (about 19–19.05 × 9.5–9.53 mm). Lengths run 12–48+ in, commonly 24/36/48 in.
  • Slot openings vary around 0.33–3/8 in (8.5–9.5 mm); internal cavities about 0.50–0.55 in (13–14 mm). One stepped profile has a 9/16 in (14.3 mm) upper width and 7/16 in (11.1 mm) lower recess.
  • Commonly accepts 1/4 or 5/16 in bolt shanks/heads; match the particular track.

Where it is used

Woodworking workbenches and jigsRouter/drill-press tablesCNC spoilboards, hold-down beds and clamping tablesTable-saw fixturesWorkholding

Variations

  • Predrilled countersunk universal track
  • Single-size 1/4 or 5/16 in track
  • Stepped double-cut for 1/4 in hex/T-bolts and 5/16 in T-bolts
  • Scale/tape channel
  • Intersection segment
  • Mini track
  • Heavy 3/8 in or combined miter/T-track
  • Structural 80/20-style T-slot (different profile)

How to recognise it

Recognized by a 3/4" wide by 3/8" deep rectangular outer cross-section with an internal channel stepped on the inside (double-cut / stacked profile) to accommodate both hexagonal bolt heads and rounded rectangular T-bolt heads.

Often confused with

Confused withHow to tell them apart
Mini T-trackMini T-track typically only accepts 1/4" hex bolts or small proprietary sliders, not 5/16" or standard wide T-bolts.
Standard 3/4" x 3/8" miter trackStandard miter gauge tracks accept a solid rectangular miter guide bar or wide T-bar, not narrow sliding T-bolts/hex bolts.
Industrial T-slot structural framing (e.g., 2020 / 8020 / Bosch Rexroth)Structural framing uses metric/fractional multi-face aluminum extrusions designed for framework erection rather than flush-mounted workbench jig guidance.
Standard 3/4" x 3/8" miter gauge slotMiter slots are rectangular guide channels designed for sliding miter bars without captive overhang lips unless fitted with a bottom T-bar groove. Miter slots are open rectangular channels (sometimes with a bottom T-lip for miter bars) sized to fit a 3/4" guide bar, whereas Universal T-track has top retaining lips with a narrow 3/8" center opening.
Industrial T-slot framing (e.g. 80/20, Bosch Rexroth)Framing extrusions have hollow box structural cross sections with slots on multiple faces, whereas woodworking T-track is a shallow single-channel extrusion embedded in a dado.

Also called

Double-cut profile T-trackStacked-slot T-track3/4" x 3/8" T-trackmiter track channelUniversal T-slot track; Universal T-slot extrusionMulti-trackWoodworking T-slot trackMiter T-track

Good to know

Commonly referred to as 'Universal' because its stepped cavity solves incompatibility between older 1/4" hex bolt systems and dedicated 1/4" or 5/16" T-slot bolts.

Related connections

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro