Connection Types Wiki · Plumbing fittings

Bathtub Overflow Flange-and-Gasket Opening

A circular through-hole penetration in the side wall of a bathtub shell designed to receive a waste and overflow drain fitting. The overflow flange seals against the exterior shell surface via a gasket while an escutcheon faceplate fastens from the interior.

Illustration of a Bathtub Overflow Flange-and-Gasket Opening
Gender
female
Connects by
clamp, fastened, compression
Standards
ASME A112.18.2; CSA B125.2; ASME A112.19.1; ASME A112.19.2; CSA B45.5 / IAPMO Z124; CSA B45.2
Regions
North America, worldwide

How it connects

Clamped through the shell opening using machine screws passing through a decorative overflow faceplate from the inside, compressing a rubber/foam wedge gasket between the tub shell exterior and the overflow pipe elbow flange.

Male and female halves

Female opening/cutout in the bathtub shell that receives a male alignment boss or clamping screws from the overflow elbow on the exterior and faceplate on the interior.

Usually connects to

  • Matching bath waste/overflow elbow with gasket, faceplate/screws or retaining bracket
  • Compatible trip-lever linkage
  • Model-specific slotted overflow assembly, such as Kohler Clearflo K-7271/K-7272

Common sizes

  • Round overflow holes typically 2–2-1/2 in (50–64 mm), often 2-1/8–2-1/4 in in North America; faceplates around 3–3-1/4 in, with one- or two-screw patterns.
  • A separate slotted style is described around 20 mm high × 100–120 mm wide.
  • Downstream waste/overflow tube commonly 1-1/2 in PVC or brass.

Where it is used

Bathtub manufacture/installationWaste/overflow and sanitary DWV assembliesResidential bathroom/hospitality plumbingAcrylic/cast-iron soaking tubs

Variations

  • One-center-screw or two-screw faceplate
  • Slotted/integral overflow
  • Screwless snap/click bracket or cover
  • Trip-lever plate
  • Beveled or flat gasket
  • Integrated gasket/cover kit

How to recognise it

A round penetration (typically 2" to 2-1/2" diameter) drilled or molded near the top rim on the interior side or end wall of a bathtub shell, positioned directly above the floor drain.

Often confused with

Confused withHow to tell them apart
Bathtub drain shell through-openingLocated on the tub floor rather than the upper sidewall, designed for vertical drain flange installation (usually 1-1/2" IPS thread and recessed bevel).
Integral slotted bathtub overflowFeatures a pre-molded horizontal slot channel molded into the acrylic/composite shell rather than a round through-hole opening.
tub drain shoe / drain flange connectionThe drain is in the tub floor and uses a threaded drain strainer into the shoe; the overflow is on the end wall and uses screws through a faceplate.
bathtub bottom drain holeThe overflow hole is located high on the vertical/sloped sidewall rather than in the floor of the tub, and relies on an external clamp/gasket rather than a threaded drain flange strainer basket.
Threaded bathtub drain outletThe bottom drain uses a strainer/flange threaded into a drain shoe; this interface is the smooth overflow opening higher on the tub wall.

Also called

bathtub overflow hole; bathtub overflow openingtub overflow cutout; Tub overflow holeoverflow plate and gasket; overflow cover plate mountwaste and overflow (W&O) overflow flangebath waste and overflow port; slotted bath overflowtub overflow drain openingGasketed tub overflow mounting interfaceKohler Clearflo slotted overflow opening

Good to know

Described on manufacturer bathtub specification sheets as the overflow hole or opening. It serves as a mounting port for standard waste and overflow (W&O) plumbing trim kits. Additional standard references: IAPMO/ANSI Z124.1.2; CSA B45.1.

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro