Connection Types Wiki · Plumbing fittings

Kitchen Basket-Strainer Flange Opening

A circular recessed opening in the bottom of a sink basin designed to receive and support a basket strainer assembly or garbage disposal flange.

Illustration of a Kitchen Basket-Strainer Flange Opening
Gender
female
Connects by
clamp, compression, fastened, insertion, threaded
Standards
ASME A112.18.2; CSA B125.2; ASME A112.19.3; CSA B45.4
Regions
worldwide, North America

How it connects

The strainer body drops into the opening from above, sealed under its top flange with plumber's putty or a gasket, and is clamped tightly to the sink bowl from underneath using a rubber washer, friction ring, and large threaded locknut.

Male and female halves

Female receptacle/seat (the sink bowl's hole with recessed bevel) mating with the male body flange of a basket strainer or disposal mount.

Usually connects to

  • Matching basket-strainer/drain assembly for the sink opening, commonly nominal 3-1/2 in
  • Compatible disposer sink flange/mount, including deep/extended flanges

Common sizes

  • Kitchen openings commonly nominal 3-1/2 in (88.9 mm), with listed holes around 3-1/2–3-5/8 in (about 89–92 mm). Some hardware accepts 3-1/2–4 in; this is a fit range, not a hole tolerance.
  • Strainer rims commonly 4-1/4–4-1/2 in; outlets typically use 1-1/2 in tailpieces.
  • Bar/prep sinks may use 2–2-1/2 in openings; lavatories 1-1/4–1-1/2 in. Some European waste openings are about 114 mm. Match seat shape and sink thickness.

Where it is used

Residential/commercial kitchen/compartment sink drainsUtility/laundry and bar/prep sinksGarbage-disposer installation

Variations

  • 3-1/2 in kitchen, 2/2-1/2 in bar/prep or Euro 90 mm opening
  • Thin/thick sink version with corresponding flange length
  • Locknut or screw-clamped strainer/retainer
  • Model-specific disposer flange
  • Deep/offset basket
  • Flat-bottom seat

How to recognise it

A circular cutout centered or offset in the basin floor, typically pressed or cast with a slightly recessed or beveled shoulder so the flange of the strainer sits flush with or below the basin bottom for complete water drainage.

Often confused with

Confused withHow to tell them apart
Bathroom lavatory sink drain openingLavatory sink drain openings are significantly smaller (usually 1-1/4" to 1-1/2" diameter) and mate with pop-up drain assemblies rather than 3-1/2" basket strainers.
Strainer tailpiece connectionThe tailpiece connection is a 1-1/2" slip-joint or flanged coupling underneath the strainer outlet leading to the P-trap, whereas the strainer seat is the physical opening in the sink basin itself.
Female pipe threadThe sink opening is a smooth hole with a sealing rim, without helical internal threads.
Removable basket or stopper interfaceA replacement basket fits inside an already installed drain body; this entry describes the hole through the sink that receives the whole drain assembly.
Disposal-to-flange mounting interfaceThe disposer mounts below the sink onto its own compatible hardware; a shared sink-hole size does not guarantee disposer mounting compatibility.

Also called

kitchen sink drain holebasket strainer hole3-1/2 inch sink drain hole; 3-1/2 inch kitchen sink drain openingkitchen sink waste openingbasket-strainer mounting openingstandard kitchen sink drain outletstandard US kitchen sink draindisposer flange opening

Good to know

Standard North American kitchen and utility sinks feature an opening nominally rated at 3-1/2 inches (typically accepting drain bodies measuring 3.5 to 3.625 inches / 90 mm) with an outer flange counterbore.

Related connections

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro