How it connects
Radially presses over the outer diameter of the conduit with a spring snap-fit or friction grip, holding itself in place while mechanical fasteners (screws/bolts through mounting holes) clamp it firmly to the mounting surface.
Male and female halves
Female radial saddle channel receiving the male cylindrical outer diameter of the conduit.
Usually connects to
- Compatible trade-size RMC (ANSI C80.1) or IMC exterior
- EMT (ANSI C80.3) exterior
- FMC exterior
- MC/AC cable exterior
- Wall, ceiling, strut or framing through a mounting fastener
Common sizes
- Match conduit type and trade size. Listed ranges include 3/8–2 in (about 0.709–2.375 in OD) and 1/2–4 in RMC/IMC (about 0.840–4.500 in OD).
- EMT straps cover 1/2–4 in trade sizes, roughly 17.9–114.3 mm OD.
- Arlington one-hole rigid straps span 1/2–4 in; a 1/2 in trade size is not a measured 1/2 in bore.
Where it is used
Commercial/residential electrical wiring and rough-inIndustrial conduit racewaysSurface-mounted RMC/IMC supportsBeam-flange/rod/purlin hangingIndustrial strut framing
Variations
- One-/two-hole snap-on straps, stamped galvanized/zinc-plated steel
- Heavy-duty malleable-iron saddle or one-hole strap
- Multi-size snap-close clip, such as 812M for 1/2 and 3/4 in EMT/rigid
- Beam-flange clip assembly
- Conduit-to-conduit clamp
- One-/two-piece strut clamp
How to recognise it
An open curved metallic strap featuring an inner arc profiled to RMC/IMC outer diameter, usually with one or two flat mounting feet/wings with fastener clearance holes, and often an inverted bead or rib along the spine.
Often confused with
| Confused with | How to tell them apart |
|---|---|
| EMT conduit snap-on strap | EMT straps are sized for thinner outside diameters of Electrical Metallic Tubing; Rigid/IMC straps have a noticeably larger inner radius to match RMC OD. Similar appearance does not establish compatibility. Check manufacturer conduit designation and trade size; do not substitute solely by nominal size. |
| copper pipe saddle clamp | Copper pipe clamps are sized for CTS (copper tube size) outside diameters and often made of copper or copper-plated steel, whereas conduit saddles match iron pipe size (IPS) conduit OD. |
| One-hole / two-hole conduit strap | Standard straps require screws or bolts through mounting ears into a backing surface; snap-close clamps lock around conduit with integrated spring tabs and slots without fasteners on the strap closure. |
| Set-screw conduit clamp | Set-screw clamps tighten via a threaded screw pressing into the conduit wall, whereas snap-close clamps rely on spring steel band tension and locking detents. |
| Conduit-end slip or threaded connector | An end connector receives or engages a conduit end; the strap bears on the exterior of a continuing conduit run and has a mounting ear. |
Also called
rigid conduit snap-on strap; Rigid/IMC conduit straprigid conduit saddletwo-hole rigid conduit strapconduit clamp saddle; EMT saddle clampSnap close conduit clip; Snap-lock conduit clip; Snap close conduit clampSpring steel conduit clipM-series conduit clampone-piece strut clamp with saddle
Good to know
Often referred to interchangeably as a 'snap-on strap' or 'saddle'. Designed to hold onto the conduit pipe independently prior to driving the mounting fastener. Additional standard references: ANSI C80.1; ANSI C80.3.
Related connections
Design with real parts
Crafti checks which parts connect, right in your browser.




