Connection Types Wiki · Fasteners & screw threads

Female UNF Screw Thread

A tapped (internal) Unified inch screw thread of size No. 10 (0.190 in / 4.83 mm major diameter) with 32 threads per inch, the fine-pitch series. Accepts #10-32 machine screws, studs and male fittings.

Illustration of a Female UNF Screw Thread
Stands for
#10 = ASME screw gauge No. 10 (0.190 in); 32 = threads per inch; UNF = Unified National Fine.
Gender
female
Connects by
threaded, clamp, fastened, contact
Standards
ASME B1.1 (Unified Inch Screw Threads); ISO 263 (inch screw threads); ANSI B1.1; SAE J475; ISO 725; NFPA 70 (NEC) (Section 250.8; Section 250.148)
Regions
North America, worldwide (inch-based equipment), worldwide (inch-thread equipment), worldwide in inch-based equipment, worldwide (inch hardware), worldwide (inch-standard equipment), worldwide, United States

How it connects

Male #10-32 screw threads into the tapped hole and is tightened; parallel thread, so it does not seal by itself. Fluid ports seal with an O-ring, gasket or face seal (Air Logic recommends ~1 in-lb torque).

Male and female halves

This is the female (internal, tapped, class 2B) half; the male is the external screw thread (class 2A).

Usually connects to

  • #10-32 UNF male screw/bolt or stud, including green grounding screws with hex-washer/combination heads
  • Matching 10-32 miniature pneumatic/fluidic fitting
  • Matching 10-32 Microdot accelerometer connector
  • Ground wire/pigtail loop, clip or lug clamped by the grounding screw

Common sizes

  • #10-32 UNF: 0.190 in (4.83 mm) major diameter, 32 TPI, 0.794 mm pitch; typical tap drill #21 (0.159 in).
  • Ground screws commonly 3/8 or 1/2 in long; thread depth varies, often in a raised/extruded sheet-metal boss. Related but different threads include #10-24 and #8-32 UNC.

Where it is used

Electrical/weatherproof/junction boxes, grounding/cover screws and fan/fixture mountsResidential/commercial wiringMiniature pneumatics/fluidicsInstrumentation/vibration sensorsOptics/laboratory hardwareMachinery fasteners

Variations

  • UNF-2B (standard); UNF-3B (tight tolerance)
  • UNEF/UNR-related forms
  • threaded insert (helicoil) version
  • tapped hole in raised boss; tapped hole with factory-installed green screw
  • self-tapping ground screw into plain hole
  • #10-24 UNC (coarse)
  • class 1B/2B/3B fits; thread class 2B (general) or 3B (precision)
  • through hole vs blind hole; extruded sheet-metal boss vs machined hole

How to recognise it

Small tapped hole about 4.8 mm across with fine threads (32 per inch); often marked '10-32' near pneumatic ports. Smaller than 1/4-20 and finer than 10-24; tap drill #21.

Often confused with

Confused withHow to tell them apart
#10-24 UNCSame 0.190 in diameter but coarser: 24 TPI vs 32 TPI; a 10-24 screw will not thread into a 10-32 hole.
M5 x 0.8 metricM5 is 5.0 mm diameter with 0.8 mm pitch, very close to 10-32 (4.83 mm, 0.794 mm); they may start but bind. Check with a thread gauge or the part's unit system.
NPT pipe threadNPT is tapered and much larger; 10-32 is a small parallel machine thread. Conduit hubs are large threaded openings for conduit; the ground seat is a small screw hole.
#8-32 / #6-32 device and cover screw holesDevice/cover mounting holes are usually 6-32 or 8-32 at the ears/corners; the ground hole is the larger 10-32 one, often marked GR/GRD or in a raised dimple at the back.
#8-32 UNCSame 32 TPI but smaller (0.164 in). It's used for device/cover screws on electrical boxes, while 10-32 is for fan and fixture mounting.

Also called

No. 10-32 UNF-2B; 10-32 2B thread; No. 10-32 internal threadM5-ish 10-32 port (pneumatics)Microdot 10-32 (in sensors)ground screw holegrounding screw tap10-32 ground hole; 10-32 UNF tapped holebonding screw bossM4.8x0.79 (approx. metric equivalent)

Good to know

On an electrical weatherproof box, 10-32 holes are typically for ground screws. The same thread is also used for miniature pneumatic ports.

Related connections

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro