Connection Types Wiki · Fasteners & screw threads

Female UNC Screw Thread

The pair of tapped #6-32 UNC holes in a North American electrical/raceway device box (or mud ring/extension) that the mounting yoke (strap) of a receptacle, switch or other wiring device screws into, on the standard 3-9/32 in. (83.3 mm) single-gang centers.

Stands for
6-32 = ASME/Unified #6 screw size (0.138 in. major diameter), 32 threads per inch; UNC = Unified National Coarse.
Gender
female
Connects by
threaded, fastened
Standards
ASME B1.1 (Unified inch screw threads); NEMA OS 1; UL 514A (metallic outlet boxes); NEMA WD 6 (wiring device dimensions, yoke mounting); UL 514D (for device and plate dimensions); UL 514C (nonmetallic outlet boxes)
Regions
North America, worldwide (inch-based products), worldwide in US-inch hardware, worldwide in inch-based equipment, Worldwide where inch fasteners are specified, worldwide in inch-based hardware

How it connects

A #6-32 machine screw passes through the device yoke's slotted ear and threads into the tapped hole in the box tab; no seal. Wall plate screws then thread into the device yoke (also 6-32).

Male and female halves

This is the female (tapped/internal thread) half in the box; the male half is the #6-32 device mounting screw captive in the device yoke.

Usually connects to

Common sizes

  • #6-32 UNC is conventional for US/Canadian wiring-device and wallplate screws: 0.138 in major diameter, about 0.11 in (2.8 mm) pilot hole.
  • Device mounting holes lie on 3-9/32 in (83.3 mm) vertical centres, with 1.81 in (46 mm) gang spacing.
  • Common screw lengths are 3/8–1 in for plates and 1/2–2 in for devices/extensions. Box-cover and grounding screws may instead be #8-32 or #10-32.

Where it is used

Wiremold 500/700 and other device boxesSwitch/outlet boxes, old/new workMud rings/extendersResidential/commercial receptacles, switches and GFCI/AFCI devicesSwitch/receptacle wallplates

Variations

  • tapped hole in sheet-metal box ear; single tapped hole (toggle/rocker style plates); two holes on standard toggle/duplex plates
  • threaded brass insert in plastic box
  • self-tapping hole for thread-forming screws in nonmetallic boxes
  • decorator (2 screws, outside rectangular opening); toggle switch plate (2 screws)
  • standard duplex receptacle plate (1 center screw, same 6-32 thread)
  • screwless snap-on plates using a sub-plate screwed into the same holes
  • decorator/Decora (rocker) strap holes, at the top and bottom of the strap
  • molded plastic boss (self-threading)

How to recognise it

Two small tapped holes, about 3.5 mm diameter, on tabs or ears at the top and bottom center of the box opening, spaced 83.3 mm (3-9/32 in.) apart.

Often confused with

Confused withHow to tell them apart
#8-32 box cover / mud ring screw holes8-32 holes are at the box corners (diagonal) for covers and rings; 6-32 device holes are top and bottom center on 3-9/32 in. centers. #8-32 is larger (0.164 in diameter), used for some box covers and ground screws, not wallplates.
#10-32 grounding screw holeSingle hole usually in the back or side of the box, often green screw, not paired at top/bottom.
#6-32 device mounting screw holes / box earsDevice-to-box mounting uses #6-32 screws through slots at the strap ends into the box; the wallplate holes are tapped holes in the strap closer to the device face.
#6-32 device mounting screw into the electrical boxThe box mounting screws pass through the slotted ends of the strap into the box's ears. The plate-screw holes are tapped holes nearer the device body.
#8-32 UNCLarger diameter (0.164 in), used for some box and cover fastenings; the thread pitch is the same, so measure the diameter.

Also called

device mounting screw hole6-32 device ears / device screw holes; 6-32 wall plate screw hole#6-32 tapped device mounting hole; 6-32 tapped hole on device yokestrap screw holecover plate screw thread; switch plate screw threaddevice yoke plate-screw hole6-32 tapped eardevice mounting boss

Good to know

US electrical device screws conventionally use #6-32 thread and 3-9/32 in. mounting spacing. Additional standard references: ASME B18.2.2 (hex nuts).

Related connections

Design with real parts

Crafti checks which parts connect, right in your browser.

Start a Project

Crafti Free

Everything you need to start designing.

Parts

  • 22,100+ real parts in 346 categories
  • Configurable parts
  • Real-world textures

Build

  • Snap-to-connect
  • See what connects to what
  • Auto-adjust by joints
  • Build once, repeat many
  • Draw & cut shapes

Precision

  • Easy 3D positioning
  • Make it flush
  • Point & click measuring
  • Scale references

Plan & buy

  • Live parts list
  • Cut plan for stock lengths
  • Fill your cart at retailers

Workspace

  • Works in your browser and on your phone
  • Backdrop reference images
  • Save up to three designs
Start designing for free

Need more? See Crafti Pro