How it connects
Self-tapping threaded mechanical connection where external rolled threads with W-Cut serrations cut internal matching threads directly into wood fibers, drawing members tight under a built-in washer head.
Male and female halves
Male externally threaded fastener shank that mates directly into wood substrates (which serve as the female mating matrix) without requiring a pre-tapped female nut.
Usually connects to
- Wood framing, structural lumber or timber with the specified pilot hole
- Engineered wood including LVL, PSL, LSL and glulam
- Matching masonry lag shield/expansion anchor or plastic/lead wall anchor
Common sizes
- Lag screws commonly 1/4–1 in diameter, with metric coach-screw ranges M6–M20/M24; wood screws include #2–#24.
- Examples: #10 thread OD 0.194 in, 1/4 in = 0.250 in, 5/16 in = 0.3125 in and 3/8 in = 0.375 in. Lengths commonly 1-1/2–16 in, up to 20 in for timber.
- Coarse pitches vary: about 7 TPI (3.6 mm) at 3/8 in or 5 TPI at 5/8 in; one 5/8 in hook was measured near 5 mm pitch.
- A 1/4 in screw-eye example is 3-3/4 in overall; nominal diameter alone does not specify pitch, thread length or tolerance.
Where it is used
Structural/timber wood framingDeck ledgers, beams and postsStair railsHook/eye, pintle and bracket mountsUtility-pole hardware
Variations
- Climatek coated carbon steel
- PHEinox 305 / 316 stainless steel
- RSS Black structural screw; RSS LTF (Timber Frame Screw)
- RSS JTS (Joist and Truss Screw)
- gimlet (cone) point
- screw hook / screw eye / pintle with lag-thread shank; Screw-eye ends; Screw-hook ends
- hanger bolt (lag thread one end, machine thread other)
- Hex-head or square-head lag screws
How to recognise it
Deep aggressive wood threads terminating in a fluted Zip-Tip point, tiny serrated razor-like ridges running perpendicular along the thread crests (W-Cut), and knurled spiral flutes (CEE-Thread) on the shank directly above the thread.
Often confused with
| Confused with | How to tell them apart |
|---|---|
| Standard lag screw / lag bolt thread | Traditional lag screws have standard ASME B18.2.1 wood screw / hex lag threads requiring pilot holes, lacking W-Cut serrations, Zip-Tip, and CEE-threads. |
| Simpson Strong-Tie SDS / SDWS structural screws | Simpson screws feature patented 4-cut tips or serrated knurled shanks rather than GRK's specific W-Cut thread serrations and CEE-thread reamer geometry. |
| NPT pipe thread | NPT has a fine 60° thread on a blunt tapered end and mates with a female fitting. A lag thread is coarse and widely spaced, and ends in a sharp point. |
| Machine (UNC) thread | UNC has a constant diameter, a blunt end and a finer pitch, and needs a nut or tapped hole. |
| Small wood screw thread | It looks the same, but lag threads are larger (1/4 in. and up) and usually come with hex heads or heavy shanks. |
Also called
GRK RSS threadGRK Rugged Structural Screw threadW-Cut threadlag bolt threadgimlet-point wood screw threadcoach screw thread (UK)Lag-thread screw endType 17 wood screw
Good to know
Engineered as an ICC-ES ESR-2442 code-approved high-strength replacement for traditional 3/8 in and 1/2 in lag bolts without requiring pre-drilling. Additional standard references: ASME B18.6.1 (wood screws).
Design with real parts
Crafti checks which parts connect, right in your browser.
